hp2100_ipl.c:
- Exposed "ipl_edtdelay" via a REG_HIDDEN register to allow user tuning
of the EDT delay that works around a race condition in the HP
2000/Access Time-Shared BASIC system.
- Corrected typos in comments and strings.
- Merged SIMH 3.x and 4.x socket calls via conditionals, so that the
module may be compiled for either version.
hp2100_mux.c:
- Corrected a typo in the RTS macro definition.
hp2100_sys.c:
- Added a cast to int for the parameter to "isspace" to avoid a compiler
warning.
hp2100_bugfixes.txt
- Added a description of the IPL hidden register fix.
Cleanup/Simplification by:
1) removing irrelevant master flag variable from sim_close_sock and thus sim_err_sock
2) change previous boolean feature arguments (datagram, nodelay, reuseaddr) to flag bits in a single option argument. This allows for features to be added by new flag bits which don't change the calling signatures.
3) changed all status returns to be int (vs t_stat) with success being 0 and error being -1
4) removed unneeded simh specific type references to allow sim_sock to be used by n
Extended API by providing flags to influence socket setup/behavior:
SIM_SOCK_OPT_REUSEADDR Retains prior behavior when sim_switches had -U set
SIM_SOCK_OPT_DATAGRAM UDP socket setup provided for when prior datagram argument was specified
SIM_SOCK_OPT_NODELAY TCP Nagle disable provided for when prior nodelay argument was specified
SIM_SOCK_OPT_BLOCKING Blocking socket mode (detault is non blocking)
265. PROBLEM: Compiling the HP simulator for 64-bit addressing produces many
conversion warnings.
OBSERVATION: Compiling the simulator and defining USE_INT64 and USE_ADDR64
with implicit conversion warnings enabled reveals a number of places where
assumptions were made that addresses would always be 32 bits. This is a
reasonable assumption, as there are no devices (CPU or peripherals) that
can handle gigabyte addressing. Still, many of these assumptions are not
necessary, and some future peripheral simulator may exceed this limit.
CAUSE: Future expansion to 64-bit addressing was not envisioned.
RESOLUTION: Modify source files to ensure that "t_addr" and "t_value"
types are used instead of "uint32" and "int32" types where addressing and
data values may be 64 bits. Also ensure that valid conversions to smaller
sizes use explicit casts.
266. PROBLEM: BOOT devices require a duplicate S-register declaration.
OBSERVATION: All of the peripheral devices that support the BOOT command
set the select code and other parameters into the S register during the
boot process. This direct register access requires an external declaration
that duplicates the one in the full CPU declarations file (hp2100_cpu.h).
A better method that avoids the duplicate declaration would be for the
"ibl_copy" routine to modify the S register on behalf of the caller.
CAUSE: Poor original implementation.
RESOLUTION: Modify "ibl_copy" (hp2100_cpu.c) to take two additional
parameters that clear and set bits, respectively, in the S register on
behalf of the caller. Modify the boot routines for the CPU, DA, DP, DQ,
DR, DS, IPL, MS, and PTR devices to use the new parameters instead of
modifying the S register directly.
OBSERVATION: The HP 2100 MS device simulates the HP 7970 B/E magnetic tape
drives. The 7970B uses NRZI format, and its associated controller supports
returning the cyclic redundancy check character and longitudinal redundancy
check character (CRCC and LRCC) to the CPU. Typically, these are used only
by the controller diagnostic, but support is easy to add.
RESOLUTION: Modify "hp2100_ms.c" to add a function that calculates CRCC
and LRCC for reads and writes, and call that function when the CPU requests
that the controller deliver the values.
Added support for per line tcp listen ports.
Added support for per line outgoing tcp/telnet connections.
Removed DEV_NET from pdp11_dz and pdp11_vh emulators to allow proper restore of
It also modifies the HP 2100 and PDP11 multiplexers to add serial support as demonstrations of the capability that, one day, might be extended to all simulators. I have tested the HP support, but I relied on Holger Veit to test the DEC stuff, so I can't guarantee that it works. I also relied on Holger to test under Linux, so the same caveat applies.
The changes needed in the device simulators are relatively small. For example, if you look at the patches for "hp2100_baci.c", you'll note that most of them are documentation changes. The only things of note are:
- an expansion of the TMXR initializer
- additional code in the "attach" routine to try attaching a serial port
if attaching a socket fails
- additional code in the "detach" routine for the same reasons
The HP MPX device (hp2100_mpx.c) needs a tiny bit of additional support from the ATTACH and DETACH commands. Specifically, SCP was modified to set a flag ("sim_unit_ref") to indicate whether ATTACH MPX or ATTACH MPX0 was done, i.e., to differentiate between a device and a unit attach (recall that SCP treats these as both referring to unit 0). This is needed because the socket attaches (logically) to the device, whereas a serial port attaches to a line. Without this flag, the attach routine cannot differentiate between ATTACH MPX and ATTACH MPX0, as the distinction is lost by the time the VM's attach routine is called. This support isn't needed for the HP MUX device because the socket attaches to a different device than the lines do.
MPX also requires a bit more work due to the capability to mix serial and Telnet lines on the same multiplexer (BACI is a single-line terminal device).
The attached PDF contains revisions to the "Writing a Simulator for the SIMH System" publication that documents the additions and changes to the multiplexer library for serial port support. User documentation for serial port support currently exists only in the initial comments in "sim_tmxr.c"; I will add the appropriate text to the "SIMH User's Guide" if we decide to add this to the release version.
The makefile now works for Linux and most Unix's. However, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.1.2 GRI
- Added support for the GRI-99 processor.
1.1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
1.2 3.8-1
1.2.1 SCP and libraries
- Added capability to set line connection order for terminal multiplexers.
1.2.2 HP2100
- Added support for 12620A/12936A privileged interrupt fence.
- Added support for 12792C eight-channel asynchronous multiplexer.
1.3 3.8-2
1.3.1 SCP and libraries
- Added line history capability for *nix hosts.
- Added "SHOW SHOW" and "SHOW <dev> SHOW" commands.
1.3.2 1401
- Added "no rewind" option to magtape boot.
1.3.3 PDP-11
- Added RD32 support to RQ
- Added debug support to RL
1.3.4 PDP-8
- Added FPP support (many thanks to Rick Murphy for debugging the code)
1.3.5 VAX-11/780
- Added AUTORESTART switch support, and VMS REBOOT command support
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The makefile now works for Linux and most Unix's. However, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.1.2 GRI
- Added support for the GRI-99 processor.
1.1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
1.2 3.8-1
1.2.1 SCP and libraries
- Added capability to set line connection order for terminal multiplexers.
1.2.2 HP2100
- Added support for 12620A/12936A privileged interrupt fence.
- Added support for 12792C eight-channel asynchronous multiplexer.
1.3 3.8-2
1.3.1 1401
- Added "no rewind" option to magtape boot.
1.3.2 PDP-11
- Added RD32 support to RQ
- Added debug support to RL
1.3.3 PDP-8
- Added FPP support (many thanks to Rick Murphy for debugging the code)
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The makefile now works for Linux and most Unix's. Howevr, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.1.2 GRI
- Added support for the GRI-99 processor.
1.1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
1.2 3.8-1
1.2.1 SCP and libraries
- Added capability to set line connection order for terminal multiplexers.
1.2.2 HP2100
- Added support for 12620A/12936A privileged interrupt fence.
- Added support for 12792C eight-channel asynchronous multiplexer.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The makefile now works for Linux and most Unix's. Howevr, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.2 GRI
- Added support for the GRI-99 processor.
1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
1. New Features
1.1 3.7-0
1.1.1 SCP
- Added SET THROTTLE and SET NOTHROTTLE commands to regulate simulator
execution rate and host resource utilization.
- Added idle support (based on work by Mark Pizzolato).
- Added -e to control error processing in nested DO commands (from
Dave Bryan).
1.1.2 HP2100
- Added Double Integer instructions, 1000-F CPU, and Floating Point
Processor (from Dave Bryan).
- Added 2114 and 2115 CPUs, 12607B and 12578A DMA controllers, and
21xx binary loader protection (from Dave Bryan).
1.1.3 Interdata
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state.
1.1.4 PDP-11
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (WAIT instruction executed).
- Added TA11/TU60 cassette support.
1.1.5 PDP-8
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
- Added TA8E/TU60 cassette support.
1.1.6 PDP-1
- Added support for 16-channel sequence break system.
- Added support for PDP-1D extended features and timesharing clock.
- Added support for Type 630 data communications subsystem.
1.1.6 PDP-4/7/9/15
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
1.1.7 VAX, VAX780
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (more than 200 cycles at IPL's 0, 1, or 3 in kernel mode).
1.1.8 PDP-10
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (operating system dependent).
- Added CD20 (CD11) support.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
1. New Features
1.1 3.7-0
1.1.1 SCP
- Added SET THROTTLE and SET NOTHROTTLE commands to regulate simulator
execution rate and host resource utilization.
- Added idle support (based on work by Mark Pizzolato).
- Added -e to control error processing in nested DO commands (from
Dave Bryan).
1.1.2 HP2100
- Added Double Integer instructions, 1000-F CPU, and Floating Point
Processor (from Dave Bryan).
- Added 2114 and 2115 CPUs, 12607B and 12578A DMA controllers, and
21xx binary loader protection (from Dave Bryan).
1.1.3 Interdata
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state.
1.1.4 PDP-11
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (WAIT instruction executed).
- Added TA11/TU60 cassette support.
1.1.5 PDP-8
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
- Added TA8E/TU60 cassette support.
1.1.6 PDP-1
- Added support for 16-channel sequence break system.
- Added support for PDP-1D extended features and timesharing clock.
- Added support for Type 630 data communications subsystem.
1.1.6 PDP-4/7/9/15
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
1.1.7 VAX, VAX780
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (more than 200 cycles at IPL's 0, 1, or 3 in kernel mode).
1.1.8 PDP-10
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (operating system dependent).
- Added CD20 (CD11) support.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The save/restore format has been updated to improve its reliability.
As a result, save files prior to release 3.0 are no longer supported.
The text documentation files are obsolete and are no longer included
with the distribution. Up-to-date PDF documentation files are
available on the SimH web site.
1. New Features
1.1 3.6-0
1.1.1 Most magnetic tapes
- Added support for limiting tape capacity to a particular size in MB
1.1.2 IBM 7090/7094
- First release
1.1.3 VAX-11/780
- Added FLOAD command, loads system file from console floppy disk
1.1.4 VAX, VAX-11/780, and PDP-11
- Added card reader support (from John Dundas)
1.1.5 PDP-11
- Added instruction history
1.2 3.6-1
1.2.1 PDP-11
- Added RF11 support
- Added multiple KL11/DL11 support
- Added upper-case only mode to TTI, TTO
1.2.2
- Added binary loader (courtesy of Dave Pitt)
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The save/restore format has been updated to improve its reliability.
As a result, save files prior to release 3.0 are no longer supported.
The text documentation files are obsolete and are no longer included
with the distribution. Up-to-date PDF documentation files are
available on the SimH web site.
1. New Features
1.1 3.6-0
1.1.1 Most magnetic tapes
- Added support for limiting tape capacity to a particular size in MB
1.1.2 IBM 7090/7094
- First release
1.1.3 VAX-11/780
- Added FLOAD command, loads system file from console floppy disk
1.1.4 VAX, VAX-11/780, and PDP-11
- Added card reader support (from John Dundas)
1.1.5 PDP-11
- Added instruction history
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The source set has been extensively overhauled. For correct
viewing, set Visual C++ or Emacs to have tab stops every 4
characters.
1. New Features
1.1 3.5-0
1.1.1 All Ethernet devices
- Added Windows user-defined adapter names (from Timothe Litt)
1.1.2 Interdata, SDS, HP, PDP-8, PDP-18b terminal multiplexors
- Added support for SET <unit>n DISCONNECT
1.1.3 VAX
- Added latent QDSS support
- Revised autoconfigure to handle QDSS
1.1.4 PDP-11
- Revised autoconfigure to handle more cases
1.2 3.5-1
No new features
1.3 3.5-2
1.3.1 All ASCII terminals
- Most ASCII terminal emulators have supported 7-bit and 8-bit
operation; where required, they have also supported an upper-
case only or KSR-emulation mode. This release adds a new mode,
7P, for 7-bit printing characters. In 7P mode, non-printing
characters in the range 0-31 (decimal), and 127 (decimal), are
automatically suppressed. This prevents printing of fill
characters under Windows.
The printable character set for ASCII code values 0-31 can be
changed with the SET CONSOLE PCHAR command. Code value 127
(DELETE) is always suppressed.
1.3.2 VAX-11/780
- First release. The VAX-11/780 has successfully run VMS V7.2. The
commercial instructions and compatability mode have not been
extensively tested. The Ethernet controller is not working yet
and is disabled.
2. Bugs Fixed
2.1 3.5-0
2.1.1 SCP and libraries
- Trim trailing spaces on all input (for example, attach file names)
- Fixed sim_sock spurious SIGPIPE error in Unix/Linux
- Fixed sim_tape misallocation of TPC map array for 64b simulators
2.1.2 1401
- Fixed bug, CPU reset was clearing SSB through SSG
2.1.3 PDP-11
- Fixed bug in VH vector display routine
- Fixed XU runt packet processing (found by Tim Chapman)
2.1.4 Interdata
- Fixed bug in SHOW PAS CONN/STATS
- Fixed potential integer overflow exception in divide
2.1.5 SDS
- Fixed bug in SHOW MUX CONN/STATS
2.1.6 HP
- Fixed bug in SHOW MUX CONN/STATS
2.1.7 PDP-8
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.1.8 PDP-18b
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.1.9 Nova, Eclipse
- Fixed potential integer overflow exception in divide
2.2 3.5-1
2.2.1 1401
- Changed character encodings to be compatible with Pierce 709X simulator
- Added mode for old/new character encodings
2.2.2 1620
- Changed character encodings to be compatible with Pierce 709X simulator
2.2.3 PDP-10
- Changed MOVNI to eliminate GCC warning
2.2.4 VAX
- Fixed bug in structure definitions with 32b compilation options
- Fixed bug in autoconfiguration table
2.2.5 PDP-11
- Fixed bug in autoconfiguration table
2.3 3.5-2
2.3.1 PDP-10
- RP: fixed drive clear not to clear disk address
2.3.2 PDP-11 (VAX, VAX-11/780, for shared peripherals)
- HK: fixed overlap seek interaction with drive select, drive clear, etc
- RQ, TM, TQ, TS, TU: widened address display to 64b when USE_ADDR64 option selected
- TU: changed default adapter from TM02 to TM03 (required by VMS)
- RP: fixed drive clear not to clear disk address
- RP, TU: fixed device enable/disable to enabled/disable Massbus adapter as well
- XQ: fixed register access alignment bug (found by Doug Carman)
2.3.3 PDP-8
- RL: fixed IOT 61 decoding bug (found by David Gesswein)
- DF, DT, RF: fixed register access alignment bug (found by Doug Carman)
2.3.4 VAX
- Fixed CVTfi to trap on integer overflow if PSW<iv> is set
- Fixed breakpoint detection when USE_ADDR64 option selected
The source set has been extensively overhauled. For correct
viewing, set Visual C++ or Emacs to have tab stops every 4
characters.
1. New Features
1.1 3.5-0
1.1.1 All Ethernet devices
- Added Windows user-defined adapter names (from Timothe Litt)
1.1.2 Interdata, SDS, HP, PDP-8, PDP-18b terminal multiplexors
- Added support for SET <unit>n DISCONNECT
1.1.3 VAX
- Added latent QDSS support
- Revised autoconfigure to handle QDSS
1.1.4 PDP-11
- Revised autoconfigure to handle more casees
2. Bugs Fixed
2.1 3.5-0
2.1.1 SCP and libraries
- Trim trailing spaces on all input (for example, attach file names)
- Fixed sim_sock spurious SIGPIPE error in Unix/Linux
- Fixed sim_tape misallocation of TPC map array for 64b simulators
2.1.2 1401
- Fixed bug, CPU reset was clearing SSB through SSG
2.1.3 PDP-11
- Fixed bug in VH vector display routine
- Fixed XU runt packet processing (found by Tim Chapman)
2.1.4 Interdata
- Fixed bug in SHOW PAS CONN/STATS
- Fixed potential integer overflow exception in divide
2.1.5 SDS
- Fixed bug in SHOW MUX CONN/STATS
2.1.6 HP
- Fixed bug in SHOW MUX CONN/STATS
2.1.7 PDP-8
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.1.8 PDP-18b
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.1.9 Nova, Eclipse
- Fixed potential integer overflow exception in divide
2.2 3.5-1
2.2.1 1401
- Changed character encodings to be compatible with Pierce 709X simulator
- Added mode for old/new character encodings
2.2.2 1620
- Changed character encodings to be compatible with Pierce 709X simulator
2.2.3 PDP-10
- Changed MOVNI to eliminate GCC warning
2.2.4 VAX
- Fixed bug in structure definitions with 32b compilation options
- Fixed bug in autoconfiguration table
2.2.5 PDP-11
- Fixed bug in autoconfiguration table
The source set has been extensively overhauled. For correct
viewing, set Visual C++ or Emacs to have tab stops every 4
characters.
1. New Features in 3.4-1
1.1 All Ethernet devices
- Added Windows user-defined adapter names (from Timothe Litt)
1.2 Interdata, SDS, HP, PDP-8, PDP-18b terminal multiplexors
- Added support for SET <unit>n DISCONNECT
1.3 VAX
- Added latent QDSS support
- Revised autoconfigure to handle QDSS
1.4 PDP-11
- Revised autoconfigure to handle more casees
2. Bugs Fixed in 3.4-1
2.1 SCP and libraries
- Trim trailing spaces on all input (for example, attach file names)
- Fixed sim_sock spurious SIGPIPE error in Unix/Linux
- Fixed sim_tape misallocation of TPC map array for 64b simulators
2.2 1401
- Fixed bug, CPU reset was clearing SSB through SSG
2.3 PDP-11
- Fixed bug in VH vector display routine
- Fixed XU runt packet processing (found by Tim Chapman)
2.4 Interdata
- Fixed bug in SHOW PAS CONN/STATS
- Fixed potential integer overflow exception in divide
2.5 SDS
- Fixed bug in SHOW MUX CONN/STATS
2.6 HP
- Fixed bug in SHOW MUX CONN/STATS
2.7 PDP-8
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.8 PDP-18b
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.9 Nova, Eclipse
- Fixed potential integer overflow exception in divide
