These changes facilitate more robust parameter type checking and helps
to identify unexpected coding errors.
Most simulators can now also be compiled with a C++ compiler without
warnings.
Additionally, these changes have also been configured to facilitate easier
backporting of simulator and device simulation modules to run under the
simh v3.9+ SCP framework.
Here's a PDP11 SIMH bug as old as the simulator itself: the reset_cpu routine sets the PS to 340 (interrupts disabled). This causes some versions of Lunar Lander not to work. In fact, the initial state of the PS is not architecturally standardized:
04: cleared (from schematics)
05: cleared (from manual)
20: cleared (from schematics)
34: cleared (from schematics), set to 340 on boot?
40: cleared (from schematics)
44: cleared on init, set to 340 on boot (from schematics, manual)
45: cleared (from schematics)
60: cleared (from schematics)
70: cleared (from schematics)
T11: set to 340 (from spec)
LSI11, F11: 4 mode behavior (from memory on power recovery, cleared on GO, 340 on boot, mode 3 undefined)
J11: 4 mode behavior (from memory on power recovery, cleared on GO, 340 on boot, 340 on jump to custom PROM)
The story seems to be this. All non-VLSI PDP11s used TTL chips to implement the PS, either discrete flip-flops, or 4b registers, or both.
Starting with the first system, the 11/20, they were wired clear on the processor INIT signal (power-up or front panel START switch), so that all internal state started as 0. This worked fine, because START also reset the Unibus and cleared all interrupt enables. So even though the processor was as IPL = 0, no interrupts were possible. Then along came the LSI11...
The LSI11 implemented a line-time clock with NO INTERRUPT DISABLE. Thus, if IPL was left at 0 and a bootstrap routine from a slow device was started (e.g., a floppy drive), the clock would tick, and an interrupt would occur, before the bootstrap routine finished. Because no vectors were set up, the processor would crash. So the LSI11 started the practice, carried over to all later PDP11 VLSI chips, of setting the PS to 340 before jumping to a boot ROM.
The T11 did this in all modes of startup, because its only startup behavior was to jump to a "boot" routine. It did not have a console of any kind.
Accordingly, it appears that the cpu_reset routine needs to set the PS based on the processor model. Further, all boot routines need to set the PS to 0 or 340 based on the processor model. (It's probably safe for boot routines just to set the PS to 340, but it's not technically
accurate.)
Show IOSPACE doesn't always get the number of devices right due to device creativity.
o The distinction between UNIT and DEVICE has blurred
o MUX devices merge several physical devices into one device/unit
o Dynamic device sizing has made things more volatile.
This edit solves the problem for SHOW IOSPACE by adding an (optional) word to the DIBs.
The word contains the amount of IO space consumed by each instance of the physical device that's being emulated.
E.G., if it's a DZ11, the device is the DZ11 module, or 8 lines, even though the MUX device may support 32.
This enables SHOW IOSPACE to determine the number of physical devices being emulated, which is what folks need when configuring software. The word may have other uses - in a generic dynamic device sizing routine - which is why the amount of IOSPACE per device was chosen rather than the 'number of physical devices.'
The edit should not make any existing device regress. If the new word (ulnt) is zero (not initialized), SHOW IOSPACE will default to the number of units in the device, or if there's no device (CPUs), 1 as before. If it is present, the number of devices is the calculated as total allocation/allocation-per-device.
The edit updates all the devices that seem to require this treatment, and all the processors that define the UNIBUS/QBUS DIBs.
Fixed auto configure bugs which didn't allow Fixed CSR Addresses or Fixed Vectors to be set using the auto configure information.
Fixed display of address and vectors to indicate that the assigned address and/or vector is in the floating set.
Added extended definitions to the auto configure table to reflect all known potential static and floating and static addresses as of VMS V5.5-2
Changed the name of the VAX 11/780 console floppy device name to RXC from RX (which collides with a Unibus name for the RX11).
The makefile now works for Linux and most Unix's. Howevr, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.1.2 GRI
- Added support for the GRI-99 processor.
1.1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
1.2 3.8-1
1.2.1 SCP and libraries
- Added capability to set line connection order for terminal multiplexers.
1.2.2 HP2100
- Added support for 12620A/12936A privileged interrupt fence.
- Added support for 12792C eight-channel asynchronous multiplexer.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
1. New Features
1.1 3.7-0
1.1.1 SCP
- Added SET THROTTLE and SET NOTHROTTLE commands to regulate simulator
execution rate and host resource utilization.
- Added idle support (based on work by Mark Pizzolato).
- Added -e to control error processing in nested DO commands (from
Dave Bryan).
1.1.2 HP2100
- Added Double Integer instructions, 1000-F CPU, and Floating Point
Processor (from Dave Bryan).
- Added 2114 and 2115 CPUs, 12607B and 12578A DMA controllers, and
21xx binary loader protection (from Dave Bryan).
1.1.3 Interdata
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state.
1.1.4 PDP-11
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (WAIT instruction executed).
- Added TA11/TU60 cassette support.
1.1.5 PDP-8
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
- Added TA8E/TU60 cassette support.
1.1.6 PDP-1
- Added support for 16-channel sequence break system.
- Added support for PDP-1D extended features and timesharing clock.
- Added support for Type 630 data communications subsystem.
1.1.6 PDP-4/7/9/15
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
1.1.7 VAX, VAX780
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (more than 200 cycles at IPL's 0, 1, or 3 in kernel mode).
1.1.8 PDP-10
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (operating system dependent).
- Added CD20 (CD11) support.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The save/restore format has been updated to improve its reliability.
As a result, save files prior to release 3.0 are no longer supported.
The text documentation files are obsolete and are no longer included
with the distribution. Up-to-date PDF documentation files are
available on the SimH web site.
1. New Features
1.1 3.6-0
1.1.1 Most magnetic tapes
- Added support for limiting tape capacity to a particular size in MB
1.1.2 IBM 7090/7094
- First release
1.1.3 VAX-11/780
- Added FLOAD command, loads system file from console floppy disk
1.1.4 VAX, VAX-11/780, and PDP-11
- Added card reader support (from John Dundas)
1.1.5 PDP-11
- Added instruction history
1.2 3.6-1
1.2.1 PDP-11
- Added RF11 support
- Added multiple KL11/DL11 support
- Added upper-case only mode to TTI, TTO
1.2.2
- Added binary loader (courtesy of Dave Pitt)
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
