The "error" that the original change "fixed" was actually in the cmake
build system and not in the sim_ws.c code.
The Uint8 type is specific to SDL2 APIs.
- Periodic "python cmake/generate.py" to sync with makefile changes.
- Ensure that AIO_CCDEFS (makefile) and USES_AIO (CMake generate.py) are
present for PDP-10 simulators. Otherwise, user gets a warning message
when the simulator starts about network support and asynchronous I/O.
In sim_instr(), the effective address is computed; for the case of TAG
(index register addressing), the contents of the specified index register
is added to the effective address, but the result is not masked to 16
bits as per the hardware functionality.
Adding a a 16 bit mask operation fixes the issue.
Adds the following devices to AltairZ80:
TUART0: Cromemco FDC controller TUART console port at I/O address 0x00.
TUART1: Cromemco TU-ART port A at I/O address 0x20.
TUART2: Cromemco TU-ART port B at I/I address 0x50.
These devices are fully TMXR capable.
Recent analysis of the 2.9BSD kernel revealed that RP11 was
expected to interrupt on control RESET function if IE bit was
also set. Documentation was not very clear of the fact, saying
in one place that RESET+GO does not interrupt (which is not
contradictory with the above because it does not mention IE).
In other place, however, it says that IE always causes interrupt
when DONE is asserted. Thus, since RESET does assert DONE, an
interrupt should be posted if IE is set. The autoconfig binary
from 2.9BSD uses this feature of RP11 to check the presence
of the controller.
Formerly RESET was always clearing RPCS with DONE unconditionally,
and that reset IE as well. This patch makes sure that the IE bit
is preserved, and if set, it posts an interrupt when RESET asserts
DONE.
I was having problems with the JAIR device keeping up with received
data at 57.6K.
This PR makes the following changes to the JAIR devices:
- Refactors the service routines into STAT, TX and RX units
- Adds a 128-byte input ring buffer
- Corrects a null pointer exception
- Adds overrun status bit implementation
- Removes a tab with spaces
- Add the missing ibm1130.rc GUI resource file to the Windows build so
that the GUI renders correctly.
- Set the add_simulator TEST_ARGS to "-g" to fix an edge case Heisenbug
encountered during Github CI/CD tests where ibm1130 appears to hang
indefinitely on the Windows runners.
The cause is the GUI's Pump() thread function being prematurely
terminated before all GUI resources are acquired. The net result is an
infinite loop in the MS C runtime trying to exit the process with
unstable internal state. (Separate patch: synchronization across main
and Pump() threads to ensure resource acquisition completes.)
This issue never shows (cannot show) up on non-Windows platforms or
the SIMH makefile.
- Ibm1130/ibm1130_cr.c
- Fix printf() warnings (format should be long, not int)
- Signed/unsigned mismatch, size_t for array indexing
- Comment out the unused trim() function.
- Ibm1130/ibm1130_cpu.c, ibm1130_gui.c: Remove undefined static functions.
Fix divide of 0 on KS10 processor.
Fix write access for auxiliary processor memory.
Updated support new PIDP10 panel.
Allow eight Unibux ports on the TEN device.
Added GE DATANET-760 device to PDP6
Removed USER mode restriction for idle detection.
Added Data Disc 6600 Television Display System.
- Per Github messages, upgrade checkout@v3 to checkout@v4 due to an
upgrade to Node.js.
- macos-11 is now a defunct image runner. Homebrew packages either have
to compile from source or no longer install correctly.
- Update the macos compile matrix. Set CPACK_SUFFIX environment variable
to indicate macOS hardware platform: macos-14 is M1, whereas macos-12
and macos-13 are x86_64.
- Added notes with respect to the matrix.strategy runner images. The
makefile builds use "-latest" because they don't produce artifacts,
while (*) the CMake builds enumerate the images for which artifacts (+)
are produced and the runner image's name is part of the artifact.
(*) "Whilst" for the rest of the Anglosphere.
(+) "Artefact" for the rest of the Anglosphere.
Make generate.py resuable outside of open-simh, as suggested and
motivated by Richard Cornwell's simulator repository.
- Make the "experimental" rule optional. Do not generate a Python
"KeyError" if the rule is missing.
- Add documentation on how to use the CMake infrastructure outside
of open-simh: Customize the packaging.py script, season to taste.
- Update the KA10 simulator customization, moving it to its own
Python script, simgen/pdp10_simulator.py. Preparatory move that
anticipates additional frontpanel and display options.
- generate.py option "--skip-orphans": Skip the orphaned simulator
check (i.e., don't cross-reference the simulators in packaging.py
with what was scraped from the makefile.)
- Add "TEST_ARGS" argument to CMake's add_simulator function so that the
IBM 1130 simulator can pass to "-g" on the command line to disable the
GUI when running RegisterSanityCheck, i.e.:
ibm1130 RegisterSanityCheck -g
This fixes an edge case Heisenbug encountered during Github CI/CD
tests where ibm1130 appears to hang indefinitely on the Windows
runners.
The cause is the GUI's Pump() thread function being prematurely
terminated before all GUI resources are acquired. The net result is an
infinite loop in the MS C runtime trying to exit the process with
unstable internal state. (Separate patch: synchronization across main
and Pump() threads to ensure resource acquisition completes.)
This issue never shows up on non-Windows platforms or the SIMH makefile.
- cmake/generator.py, cmake/simgen: Add a "test_args" keyword argument
to the BasicSimulator constructor that holds the tests argument
parameter emitted as the "TEST_ARGS" argument to a simulator's
add_simulator(). Ensure that the IBM 1130 emits 'TEST_ARG "-g"' in its
add_simulator().
- scp.c: reset_all_p() adds 'P' to the existing switches, versus saving
sim_switches and ONLY setting the 'P' power-up reset switch. Net effect
is that the IBM 1130 simulator actually sees the 'G' flag that inhibits
the GUI during the console device reset.
IO: DVT_NOTDEV macro incorrect, Device mapping algorithm creates false dispatch points.
This mapped Multi Unit Controller and Single Unit Controller to same device.
DP, DP, MT, RAD: Test for non-existent device returns wrong status.
DP, DK, MT: TIO status should return non-operational for unattached device.
- Fix comma separator code segmentation fault: "ndigit - 3" can become a
very large unsigned number for ndigit < 3.
- dir_cmd: Allocate WildName from heap to reduce stack pressure.
- Github CI/CD: Remnant symlink issue reappeared, afflicting the
makefile-based build. For better or worse, the workaround is now
dependent on specific Python versions that must be removed, unlinked
and any remnant symlinks that HomeBrew decided it needed to install in
/usr/local/bin. The Python upgrade is triggered by the sdl2_ttf
package.
According to the Github image maintainers, this is an old, known issue
in macOS images that originates inside of Homebrew.
cmake/cmake-builder.ps1 added quotes to arguments that contained spaces,
so that arguments printed correctly for progress output. This introduced
excess quotes that caused CMake (and likely other MS apps) confusion or
argument misinterpretation.
Instead of CMake seeing a single "Visual Studio 17 2022", CMake was
actually seeing "\"Visual Studio 17 2022\"".
This patch only adds the additional quotes when reporting progress or
emitting debug output. Otherwise, command line arguments are passed
unmolested.
I7010 updated to pass diagnostics.
I7080 updated to pass diagnostics.
I7090 updated to better pass 9IOT
updated to allow Stress and other applications to run better.
Updated card punch to allow input of card decks for overpunching.
It looks like disk controllers, which automatically update
disk address (DA) after completion of I/O, are expected to do
so even if there was no data transfer because of I/O errors.
I was studying RSX-11's Error Logger documentation and
examples are clearly offsetting disk addresses backwards
by one when I/O errors are reported by the controller.
Since once the controller has found the DA-specified sector,
the I/O begins regardless of the condition of the sector (bad
or good data) or ability to transfer the contents between the
disk and the memory. If an error occurs (NXM, for instance)
the operation would stop (with the error reported) at the end
of the sector. So if, for example, the bus address register
had a bad address from the get-go, no data would be able to
transfer at all, yet DA should still be updated with DA + 1
once the controller asserts the DONE bit.
This patch makes sure that DA is always advanced when I/O has
actually been commenced.
Changing the CPU type or MEMORY size/configuration causes memory
resources mapped by other devices to be removed. This is not made
clear by "HELP CPU" and the user has no feedback that this is
happening.
This PR does the following:
1) HELP SET CPU shows that SET CPU MEMORY requires a value.
2) Feedback is provided if the value is omitted or not properly formatted.
3) Unmapped memory resources caused by a SET CPU command are displayed
on the SIMH console.
4) Adds a SET CPU RESIZEMEMORY command that resizes system memory
without unmapping other device memory resources.
- Make sure that asynchronous mode can't be changed if devices using
sim_ether are already attached.
- Add missing DEV_ETHER type flag for the only sim_ether using device
that didn't already have it.
The MEM dump command would not display past SET CPU xK memory
size. This prevented displaying ROMs or other RAM windows when
a lower amount of memory was specified. This PR changes MEM to
always display a minimum of a 64K regardless of main RAM size.
Josh's Altair/IMSAI Replacement (JAIR) is a single board computer
(SBC) for the S100 bus. I created this device to assist a friend
with getting IMP and CBBS working on his JAIR. Without having a
JAIR myself, AltairZ80 to the rescue!
The following devices are added:
JAIR - The main JAIR board I/O and ROM
JAIRS0 - Serial Port 0 (COM1)
JAIRS1 - Serial Port 1 (COM2)
JAIRP - Parallel Port
This was a bit challenging because the JAIR uses an on-board SD
card with FAT file system to hold its BIOS and CP/M disk images.
The ATTACH command is used to mount SD card images to the
simulator. The simulator emulates the SD card interface for
read/writing SD card sectors. These images are easily mounted on
a Mac making moving files around easy. I do not know about Windows.
These same images can be written to an SD card and used with real
JAIR hardware, which may be useful for JAIR owners.
The serial and parallel ports fully support TMXR. Host serial ports
and sockets may be attached to these devices.
I am working on a GitHub repository containing an SD card image and
init script that will boot CP/M 2.2 on the JAIR simulator.
Is this device one that should be added to AltairZ80?
SCP doesn't initially adjust timer calibrations if SET THROTTLE x/t
type is enabled causing large delays in event dispatches. This PR
runs the timers through the same calibration adjustment loop as
other throttle types.
The Sol-20 provides 1K RAM at C800. This was discovered to be missing
when issuing a "SET CPU 24K" command. Without the CPU providing RAM
at C800, the Sol-20 would not function. This PR corrects the problem
by having the SOL20 device provide its own 1K RAM at C800.
(Note: Reducing compiler warnings across all, but primarily LP64
platforms, is a long term objective.)
Reduce compiler warnings on LP64 platforms (macOS, Windows) and 32-bit
builds (Win32). Prefer 'size_t' for pointer arithmetic, array indexing
and extents; 'int' hasn't been used for these purposes for many years
and across many ANSI standards. N.B. that conversions from int or int32
to size_t cause the compiler to zero-extend the value, which is
inefficient.
Refactor printf() format modifiers into sim_printf_fmts.h. Add the
SIZE_T_FMT modifier for better portability, especially on LP64 platforms
where size_t is unsigned long and sizeof(size_t) > sizeof(int).
3B2: Fix known size_t printf() format.
Issue #294: "apple silicon build problem(s?)": If the "--flavor/-f" flag
is not specified on the command line, then complain loudly, print help
and exit. The script used to default to "Unix Makefiles".
Updates:
- Add missing "-DHAVE_LIBPNG" compiler command line define when the PNG
library is detected/present for screen capture support.
- Add "clang64" to the list of MinGW64 platforms for which the
.travis/deps.sh script can install build dependencies.
- Add PThread4W_FOUND to the condition that sets async I/O for Win32
when using vcpkg for build dependencies.
- Add vs2022-x64, vs2019-x64 and vs2017-x64 build environments to
build 64-bit Windows executables.
- Use simulator AIO only where needed by the simulator (i.e., the
simulator calls/uses AIO_CHECK_EVENT in sim_instr())
- Add "USES_AIO" flag to add_simulator() to mark a simulator that
acutally uses asynchronous I/O.
- Build "_aio" SIMH core library variants that have AIO turned on,
link with the "_aio" variant when a simulator sets USES_AIO.
- Emit a warning message when WITH_ASYNC is False (CMake configuration
option) to notify the user/developer that some functionality will be
crippled.
Affected simulator builds: 3b2 family, PDP-6, PDP-11, VAX family,
IMLAC and TT2500. The makefile and cmake/generate.py also updated
to remain in sync with CMake.
N.B.: Simulators still link with the underlying platform's threading
library. SEL32 requires pthreads or equivalent threading library,
independent of AIO.
- cmake/cmake-builder.sh
- New "--no-aio" flag: Build simulators without async I/O.
- New "--no-aio-intrinsics" flag: Don't build async I/O using compiler
compare-exchange, atomic load intrinsics.
- cmake/cmake-builder.ps1
- New "-noaio" flag: Build simulators without async I/O.
- New "-noaiointrinsics" flag: Don't build async I/O using compiler
compare-exchange, atomic load intrinsics.
CMake 3.28.1 INTERFACE_LINK_LIBRARIES behavior change: The file name
must now be an absolute path. Relative paths no longer accepted.
Internally, SIMH enforces this if CMAKE_VERSION >= 3.19, when REAL_PATH
was first implemented.
Initialize de-dup'ed debug line buffer:
realloc(NULL, size) == malloc(size), which is uninitialized space.
This causes the Clang memory sanitizer to detect an attempt to read
uninitialized memory when debug_line_buf and debug_line_buf_last are
different lengths. While the uninitialized space may never actually be
compared, the memory sanitizer emits a strong hint to not do stupid.
The sanitizer trips in the i650 simulator on the first memcmp(),
debug_line_buf has 108 characters, debug_line_buf_last has 56
characters (uninitialized space follows the 56 characters, tripping
the sanitizer.)
- memset() debug_line_buf and debug_line_buf_last to zero so that
memcmp() will always gracefully return non-zero if somehow memcmp()
ends up going past the end of either buffer. Should never happen in
practice, but theory always gets mugged by reality.
- Keep track of debug_line_buf_last's comparison length (i.e., up to
the '\r') and only execute memcmp() when this length equals the
current debug_line_buf comparison length (end - endprefix + 1).
- Added a log deduplication test to "testlib" command to ensure that
nothing broke as a result of this fix.
Network ACL check in sim_addr_acl_check:
The memory sanitizer found an off-by-one bug in sim_addr_acl_check
while executing "testlib". This makes CIDR network ACLs functional,
e.g., "127.0.0.1/32" is interpreted properly and the associated
"testlib" test passes.
Python 3.12 will not have the distutils package in the standard library.
The TextFile class is particularly useful when reading [Mm]akefiles, and
recreating its functionality would be painful.
Stash a local copy of the last version of distutils.text_file.py and use
it. Do not rely on distutils being present or installed.
