Coverity flagged one magtape simulator for having fewer case breakouts
than the range of MTSE_x errors, after they were expanded for
MTSE_LEOT (listed as "V4 compatibility") and MTSE_RUNAWAY (for
Dave Bryan's implementation of erase and erase gap).
According to Dave, it turns out that MTSE_RUNAWAY can only be
returned if the magtape simulator supports and implements a density
specification and the ERASE function. The simulators Bob Supnik wrote
don't meet that criteria, so the expanded errors can't be returned.
Simply add a "default" case to the map logic returning SCPE_IERR for
unexpected cases.
Historically this functionality was reimplemented within each
DEVICE simulator often with slightly different implementations
and inconsistencies. Solving this globally within SCP required
changes in many places, but should henceforth be reasonably
managed.
As discussed in #1034
Initialize local state variables to 0. Likely non functional changes due
to lack of depth in static analysis scan. Coverity detects real problems
like this.
This avoids a potential invalid pointer dereference when formatting
the return value from sim_instr() if it is < SCPE_BASE but greater
than the previously defined static array size.sizeof
Update simh.doc to reflect this generic change.
These changes facilitate more robust parameter type checking and helps
to identify unexpected coding errors.
Most simulators can now also be compiled with a C++ compiler without
warnings.
Additionally, these changes have also been configured to facilitate easier
backporting of simulator and device simulation modules to run under the
simh v3.9+ SCP framework.
This reverts commit 5551a0dd9c.
The original idea was that the state being put into simh registers would be required to have all useful information available when remote console executed commands. These steps were taken from the code that sim_instr() executed as it was exiting. After this change was made it was realized that once a remote console command executed it might change state that directly affected instruction execution. To solve this, the logic that executes before the instructions in sim_instr() would then need to be executed whenever the event dispatch processing completed. This approach is messy, burdensome and potentially a lot of overhead for every event dispatch even though almost none of the event dispatches would be for remote console command execution. A completely different approach was suggested by J. David Bryan. That alternative approach would be to have remote console commands execute outside of the sim_instr() routine. Thus allowing the existing prelude and postlude code in sim_instr() to be performed naturally and let the remote console activities run in the same context as all other simh commands. Recent changes to scp and sim_console implement this alternative approach and thus these original changes are completely irrelevant and are thus being removed.
1. The macro to extract the printer mode bits from the unit flags word was wrong.
2. The print chains were ordered incorrectly in the print table as well.
Tested and seems to work. At least & prints as + with the Fortran chain.
The makefile now works for Linux and most Unix's. However, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.1.2 GRI
- Added support for the GRI-99 processor.
1.1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
1.2 3.8-1
1.2.1 SCP and libraries
- Added capability to set line connection order for terminal multiplexers.
1.2.2 HP2100
- Added support for 12620A/12936A privileged interrupt fence.
- Added support for 12792C eight-channel asynchronous multiplexer.
1.3 3.8-2
1.3.1 SCP and libraries
- Added line history capability for *nix hosts.
- Added "SHOW SHOW" and "SHOW <dev> SHOW" commands.
1.3.2 1401
- Added "no rewind" option to magtape boot.
1.3.3 PDP-11
- Added RD32 support to RQ
- Added debug support to RL
1.3.4 PDP-8
- Added FPP support (many thanks to Rick Murphy for debugging the code)
1.3.5 VAX-11/780
- Added AUTORESTART switch support, and VMS REBOOT command support
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The makefile now works for Linux and most Unix's. However, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.1.2 GRI
- Added support for the GRI-99 processor.
1.1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
1.2 3.8-1
1.2.1 SCP and libraries
- Added capability to set line connection order for terminal multiplexers.
1.2.2 HP2100
- Added support for 12620A/12936A privileged interrupt fence.
- Added support for 12792C eight-channel asynchronous multiplexer.
1.3 3.8-2
1.3.1 1401
- Added "no rewind" option to magtape boot.
1.3.2 PDP-11
- Added RD32 support to RQ
- Added debug support to RL
1.3.3 PDP-8
- Added FPP support (many thanks to Rick Murphy for debugging the code)
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The makefile now works for Linux and most Unix's. Howevr, for Solaris
and MacOS, you must first export the OSTYPE environment variable:
> export OSTYPE
> make
Otherwise, you will get build errors.
1. New Features
1.1 3.8-0
1.1.1 SCP and Libraries
- BREAK, NOBREAK, and SHOW BREAK with no argument will set, clear, and
show (respectively) a breakpoint at the current PC.
1.1.2 GRI
- Added support for the GRI-99 processor.
1.1.3 HP2100
- Added support for the BACI terminal interface.
- Added support for RTE OS/VMA/EMA, SIGNAL, VIS firmware extensions.
1.1.4 Nova
- Added support for 64KW memory (implemented in third-party CPU's).
1.1.5 PDP-11
- Added support for DC11, RC11, KE11A, KG11A.
- Added modem control support for DL11.
- Added ASCII character support for all 8b devices.
1.2 3.8-1
1.2.1 SCP and libraries
- Added capability to set line connection order for terminal multiplexers.
1.2.2 HP2100
- Added support for 12620A/12936A privileged interrupt fence.
- Added support for 12792C eight-channel asynchronous multiplexer.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
1. New Features
1.1 3.7-0
1.1.1 SCP
- Added SET THROTTLE and SET NOTHROTTLE commands to regulate simulator
execution rate and host resource utilization.
- Added idle support (based on work by Mark Pizzolato).
- Added -e to control error processing in nested DO commands (from
Dave Bryan).
1.1.2 HP2100
- Added Double Integer instructions, 1000-F CPU, and Floating Point
Processor (from Dave Bryan).
- Added 2114 and 2115 CPUs, 12607B and 12578A DMA controllers, and
21xx binary loader protection (from Dave Bryan).
1.1.3 Interdata
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state.
1.1.4 PDP-11
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (WAIT instruction executed).
- Added TA11/TU60 cassette support.
1.1.5 PDP-8
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
- Added TA8E/TU60 cassette support.
1.1.6 PDP-1
- Added support for 16-channel sequence break system.
- Added support for PDP-1D extended features and timesharing clock.
- Added support for Type 630 data communications subsystem.
1.1.6 PDP-4/7/9/15
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
1.1.7 VAX, VAX780
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (more than 200 cycles at IPL's 0, 1, or 3 in kernel mode).
1.1.8 PDP-10
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (operating system dependent).
- Added CD20 (CD11) support.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
1. New Features
1.1 3.7-0
1.1.1 SCP
- Added SET THROTTLE and SET NOTHROTTLE commands to regulate simulator
execution rate and host resource utilization.
- Added idle support (based on work by Mark Pizzolato).
- Added -e to control error processing in nested DO commands (from
Dave Bryan).
1.1.2 HP2100
- Added Double Integer instructions, 1000-F CPU, and Floating Point
Processor (from Dave Bryan).
- Added 2114 and 2115 CPUs, 12607B and 12578A DMA controllers, and
21xx binary loader protection (from Dave Bryan).
1.1.3 Interdata
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state.
1.1.4 PDP-11
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (WAIT instruction executed).
- Added TA11/TU60 cassette support.
1.1.5 PDP-8
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
- Added TA8E/TU60 cassette support.
1.1.6 PDP-1
- Added support for 16-channel sequence break system.
- Added support for PDP-1D extended features and timesharing clock.
- Added support for Type 630 data communications subsystem.
1.1.6 PDP-4/7/9/15
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
1.1.7 VAX, VAX780
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (more than 200 cycles at IPL's 0, 1, or 3 in kernel mode).
1.1.8 PDP-10
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (operating system dependent).
- Added CD20 (CD11) support.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
1. New Features
1.1 3.7-0
1.1.1 SCP
- Added SET THROTTLE and SET NOTHROTTLE commands to regulate simulator
execution rate and host resource utilization.
- Added idle support (based on work by Mark Pizzolato).
- Added -e to control error processing in nested DO commands (from
Dave Bryan).
1.1.2 HP2100
- Added Double Integer instructions, 1000-F CPU, and Floating Point
Processor (from Dave Bryan).
- Added 2114 and 2115 CPUs, 12607B and 12578A DMA controllers, and
21xx binary loader protection (from Dave Bryan).
1.1.3 Interdata
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state.
1.1.4 PDP-11
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (WAIT instruction executed).
- Added TA11/TU60 cassette support.
1.1.5 PDP-8
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
- Added TA8E/TU60 cassette support.
1.1.6 PDP-1
- Added support for 16-channel sequence break system.
- Added support for PDP-1D extended features and timesharing clock.
- Added support for Type 630 data communications subsystem.
1.1.6 PDP-4/7/9/15
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (keyboard poll loop or jump-to-self).
1.1.7 VAX, VAX780
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (more than 200 cycles at IPL's 0, 1, or 3 in kernel mode).
1.1.8 PDP-10
- Added SET IDLE and SET NOIDLE commands to idle the simulator in wait
state (operating system dependent).
- Added CD20 (CD11) support.
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The save/restore format has been updated to improve its reliability.
As a result, save files prior to release 3.0 are no longer supported.
The text documentation files are obsolete and are no longer included
with the distribution. Up-to-date PDF documentation files are
available on the SimH web site.
1. New Features
1.1 3.6-0
1.1.1 Most magnetic tapes
- Added support for limiting tape capacity to a particular size in MB
1.1.2 IBM 7090/7094
- First release
1.1.3 VAX-11/780
- Added FLOAD command, loads system file from console floppy disk
1.1.4 VAX, VAX-11/780, and PDP-11
- Added card reader support (from John Dundas)
1.1.5 PDP-11
- Added instruction history
2. Bugs Fixed
Please see the revision history on http://simh.trailing-edge.com or
in the source module sim_rev.h.
The source set has been extensively overhauled. For correct
viewing, set Visual C++ or Emacs to have tab stops every 4
characters.
1. New Features
1.1 3.5-0
1.1.1 All Ethernet devices
- Added Windows user-defined adapter names (from Timothe Litt)
1.1.2 Interdata, SDS, HP, PDP-8, PDP-18b terminal multiplexors
- Added support for SET <unit>n DISCONNECT
1.1.3 VAX
- Added latent QDSS support
- Revised autoconfigure to handle QDSS
1.1.4 PDP-11
- Revised autoconfigure to handle more cases
1.2 3.5-1
No new features
1.3 3.5-2
1.3.1 All ASCII terminals
- Most ASCII terminal emulators have supported 7-bit and 8-bit
operation; where required, they have also supported an upper-
case only or KSR-emulation mode. This release adds a new mode,
7P, for 7-bit printing characters. In 7P mode, non-printing
characters in the range 0-31 (decimal), and 127 (decimal), are
automatically suppressed. This prevents printing of fill
characters under Windows.
The printable character set for ASCII code values 0-31 can be
changed with the SET CONSOLE PCHAR command. Code value 127
(DELETE) is always suppressed.
1.3.2 VAX-11/780
- First release. The VAX-11/780 has successfully run VMS V7.2. The
commercial instructions and compatability mode have not been
extensively tested. The Ethernet controller is not working yet
and is disabled.
2. Bugs Fixed
2.1 3.5-0
2.1.1 SCP and libraries
- Trim trailing spaces on all input (for example, attach file names)
- Fixed sim_sock spurious SIGPIPE error in Unix/Linux
- Fixed sim_tape misallocation of TPC map array for 64b simulators
2.1.2 1401
- Fixed bug, CPU reset was clearing SSB through SSG
2.1.3 PDP-11
- Fixed bug in VH vector display routine
- Fixed XU runt packet processing (found by Tim Chapman)
2.1.4 Interdata
- Fixed bug in SHOW PAS CONN/STATS
- Fixed potential integer overflow exception in divide
2.1.5 SDS
- Fixed bug in SHOW MUX CONN/STATS
2.1.6 HP
- Fixed bug in SHOW MUX CONN/STATS
2.1.7 PDP-8
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.1.8 PDP-18b
- Fixed bug in SHOW TTIX CONN/STATS
- Fixed bug in SET/SHOW TTOXn LOG
2.1.9 Nova, Eclipse
- Fixed potential integer overflow exception in divide
2.2 3.5-1
2.2.1 1401
- Changed character encodings to be compatible with Pierce 709X simulator
- Added mode for old/new character encodings
2.2.2 1620
- Changed character encodings to be compatible with Pierce 709X simulator
2.2.3 PDP-10
- Changed MOVNI to eliminate GCC warning
2.2.4 VAX
- Fixed bug in structure definitions with 32b compilation options
- Fixed bug in autoconfiguration table
2.2.5 PDP-11
- Fixed bug in autoconfiguration table
2.3 3.5-2
2.3.1 PDP-10
- RP: fixed drive clear not to clear disk address
2.3.2 PDP-11 (VAX, VAX-11/780, for shared peripherals)
- HK: fixed overlap seek interaction with drive select, drive clear, etc
- RQ, TM, TQ, TS, TU: widened address display to 64b when USE_ADDR64 option selected
- TU: changed default adapter from TM02 to TM03 (required by VMS)
- RP: fixed drive clear not to clear disk address
- RP, TU: fixed device enable/disable to enabled/disable Massbus adapter as well
- XQ: fixed register access alignment bug (found by Doug Carman)
2.3.3 PDP-8
- RL: fixed IOT 61 decoding bug (found by David Gesswein)
- DF, DT, RF: fixed register access alignment bug (found by Doug Carman)
2.3.4 VAX
- Fixed CVTfi to trap on integer overflow if PSW<iv> is set
- Fixed breakpoint detection when USE_ADDR64 option selected
